How To Repair My Poulan Chainsaw Model P4018
Nosotros're distressing, simply our Q&A experts are temporarily unavailable.
Please bank check back afterward if you lot still haven't found the answer you need.
1 question answered by our experts.
Your search term must take 3 or more characters.
Continue searches simple. Use keywords, e.grand. "leaking", "pump", "broken" or "fit".
Sorry, nosotros couldn't find any existing answers that matched.Effort using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Does it make a difference if series# does not match on carburetor kit?
For model number P4018
Hullo Patrick, thank you for the cracking question. We but looked at 4 models all with different serials and the same P4018 model, and they all had the aforementioned carburetor Fix Number: FIX9482465 and Carburetor Adaptor Kit Fix Number: FIX9472717. Expert luck with your repair.
1 person plant this helpful.
Was this helpful?
Cheers for voting!
Both the Fuel line and the Engine fuel line, where dry rotted.
1) While still attached to the fuel tank, I first sized up the old fuel lines with the newer fuel lines.
2) With a pair of needle nose players, I then removed the sometime dry rotted fuel ?? lines, from the fuel tank.
3) I cleaned the fuel tank and around the carburetor area, to insure that there was no debris, that could perhaps fall into the path of the new fuel lines installation.
iv) I and then installed the smaller one of the fuel lines, so that information technology would be out of the manner, of the larger fuel line. I Pulled the fuel line through the smaller hole in the fuel tank, with needle nose players. I pulled the smaller fuel line out through the fuel tank filler hole, attached the fuel filter to the smaller fuel line. I Made sure that the fuel filter was extended to the furthest end of the fuel tank bottom. Six inches in all. I then fastened the smaller fuel line to the carburetor.
five) I Installed the larger fuel line, followed the aforementioned procedures as the smaller fuel line.
6) Both fuel lines where cut on an bending for piece of cake installation. No lubricant was necessary.
7) I filled upwards the fuel tank with fresh fuel and oil, new air filter and spark plug. Information technology started on the first pull. Amazing.
Parts Used:
-
Victor from SCOTTSVILLE, KY
-
Difficulty Level:
Very Piece of cake
-
Total Repair Fourth dimension:
15 - 30 mins
-
Tools:
Pliers, Socket set
6 of 7 people found this education helpful.
Was this instruction helpful to you lot?
Thank y'all for voting!
Worn out oil pump/burning chains
Subsequently checking several different videos, ordered the repair parts and two specialty tools( Clutch removal/install and a worm drive remover/installer) Total for parts and tools around 45.00. Much cheaper than the shop wanted, 85.00 to look at information technology plus parts. Every bit for results I've used the chainsaw all afternoon no trouble. Runs like it did 12 yrs agone. Pumps oil the would make Jed Clampet proud
Parts Used:
-
William from EVANSVILLE, IN
-
Difficulty Level:
Really Like shooting fish in a barrel
-
Total Repair Time:
30 - 60 mins
-
Tools:
Screw drivers, Socket set
5 of 5 people plant this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fuel and Purge lines had disintegrated
Disassembled it and cleaned fuel tank. Cutting and ran new fuel lines, installed filter and reassembled. Parts fit perfectly and got running after not running for over 20 years.
Parts Used:
-
-
Difficulty Level:
Actually Easy
-
Total Repair Time:
30 - 60 mins
-
Tools:
Nutdriver, Pliers, Spiral drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Source: https://www.partselect.com/Models/P4018/Manufacturer/123/
Posted by: belcheralwastion.blogspot.com
0 Response to "How To Repair My Poulan Chainsaw Model P4018"
Post a Comment